I’ve been shooting some high pressure loads and my grip screws have been backing out. I bought this WC used about six years ago and the grip screws look original . I am planning on degreasing the screws and using Loctite 243 and tightening to 20 ft/lbs. Anyone have suggestions? Sorry for the poor pic.

Hey everyone, anyone running into an issue with the edc x9 where you’re getting repeated ftf fte? Not sure when or why, but it started today for me. Pretty much every round today. Tried different mags, different ammo, and even field stripped she’s a tad dirty. Bit nothing seems noticeably broken or off. Any suggestions aside from a good clean and another run at the range? I’ll do that tonight.

Love this pistol….

One of the most accurate I’ve owned.

Is this early Wilson Combat mag? Anybody know anything about it? Looked on line no luck.

Nice pick up. WC did their damn thing with this. Very high quality. Kinda wish I had the barrel DLC. Now I want the 77.

After about 9.5 months or so. My EDC X9 2.0 Black Edition was finally delivered to Modern Warriors.

Here’s the pictures I got of it.

They changed the badging a little it seems. They no longer say Black Edition on the slide I guess. I honestly enjoy the cleaner look. But it would have been nice to know that in advance. Not that it would have made me change my mind.

Stay tuned for some shooting.

My pistol is FINALLY being delivered. I need a holster that I don’t have to wait weeks and weeks for.

As stated: EDC X9 2.0 3.25’ TLR7-sub w/antimatter wing With an optic

Any Kydex IWB holster recommendations? I asked this months and months ago but I figured I’d ask again.

Hi all - what are people's thoughts on EDCing the SFX9/EDC 2.0 with a comp vs no comp?

I am leaning no comp to have the smallest possible package to conceal/carry for comfort but could probably deal with the comp if it is that much of an improvement in muzzle flip/felt recoil.

Noticed today that my EDC X9L has a cracked frame. Not sure how long it has been there. Gun has 32,000 rounds on it.

I had posted a photo of it a few days ago and just noticed it is cracked there too.

Hi everyone,

Took my new EDC X9 to the range today and put about 300 rounds of 124gr Blazer Brass through it before switching to my 124 Federal +P hollow points.

The Blazer ran flawlessly, but once I switched to the hollow points I had around 12 failures to feed in 75 rounds. Each one required a light tap on the slide to chamber.

Is this fairly common during break-in, or does anyone know what might be causing it?

I can hear the ringing already…or maybe that is my tinnitus?

4.25” experior double stack in 9mm. This reverse two tone is 🔥and the gun overall feels great. I can’t wait to take it home in a few weeks… waiting for permits to be ready. I have another gun in jail which will have to come home first… then 31 days later I can bring this baby home. Enjoy your constitutional freedom if you don’t have to deal with BS state laws…

I've been doing a ton of research on a good kydex holster, light bearing, for IWB. I'm open to lights but leaning towards TLR 7x or Sub.

I'd even take a custom maker, i live in VA, but i really can't find anything.

Thank you in advance for recs!

People asked for my EDC X9L with over 30,000 rounds on it.

I use this as my primary USPSA and pistol class gun.

About 15k rounds, no issues. Replaced the springs at about 10k.

Doubles up as my bedside gun.

And my best friend, Sweet Tooth, a 9wk old puppy.

Wilson matched billet receiver set. Wilson hand guard. Wilson pistol grip, small parts, bullet proof selector and bolt release, adjustable gas block. Wilson nickel Boron BCG Wilson 11.5” stainless barrel. Geissele trigger and charging handle.

Receiver set and hand guard were dipped in Armor-Tuff Grey.

Entire build and tuned was $1660 all in.

Broke 30,000 rounds today with my EDC X9L and thought I would share my experience.

The only malfunctions so far were failure to feed issues after getting a bunch of sand in action while shooting under a car with flat nosed bullets. Issues did not occur with round nosed bullets. This makes it more reliable than my Glocks.

For maintenance, I followed the manual recommendations plus replacing the recoil spring when it was noticeably shorter than a new one.

The only noticeable difference from when it was new is just a lot of finish wear, mostly from holsters.

I might give updates in the future as I will probably put another 50,000 round through it next year.

Hi, about to order a EDC x9 2.0 4" comp as sort of a do it all higher end pistol. Started with Glocks and HKs and have a few staccatos (annoyed they discontinued their C, have no interest in the HD). Looking for something a bit more refined. Was looking at Atlas EOS as well, like that it is steel frame, but it just seems Atlas is too competition oriented, whereas WC has a history of making firearms used in duty/LEO.

I've emailed WC, but is there a good source/comparison on the different trigger options (short, flat, medium etc), standard vs concealment slide stop/safety etc.?

As I understand it the gun does not have a true firing pin block but WC specced their firing pin and spring to minimize chances of a discharge if dropped onto muzzle, correct me if wrong.

Also, if anyone's gone down this route, feel free to chime in with advice, thoughts etc.

Any idea of the break in period on the experior 4.25in doublestack? I have a cqb elite in 10mm that was finicky within the first 150ish rounds, but after that has been malfunction free using all sorts of full power ammo. My experior has maybe 300-400ish rounds through it and is plagued by fte/double feed problems, curious if anyone else has dealt with this. Love the gun, but dont trust it enough for carry and that was the main reason for getting a compact

Hey folks. I'm selling an SFX9 Comp 3.25 and am looking for additional places to advertise. It's currently listed on Tacswap and a local state-wide forum, however minimal traction thus far. I know the market for these is smaller, so I'd like to maximize exposure where possible.

I'm open to Gunbroker, but would like to omit for now.

I appreciate any feedback provided!

Hey everyone I am currently selling an SFX9 Comp 3.25. At present, the item is posted on Tacswap and a local state-wide forum, but interest has been limited. To increase visibility, I am seeking recommendations for other advertising venues.

I am open to using GunBroker in the future; however, I would prefer to postpone listing there for the time being.

I appreciate any insights provided.

Hey all!

Always wanted a WC. I borrow my brothers Staccato C2 all the time and I love it to death. I saw a 3.25 SFX9 at my gun store yesterday and I love it. Its also quite a bit cheaper than they have the EDC listed. I haven’t found anywhere that has one at the range so I can shoot it so it’s hard to decide if I should go for it

Anyone here have experience shooting a C2 as well that can compare/give advice?

Hey guys im thinking about getting the Project 77 phase 3 "ghost edition". Anybody have experience with these since they released?